kmmcrafts Posted April 6, 2022 Report Share Posted April 6, 2022 So I put my new table saw together a few minutes ago and this is so dumb on their part. I gotta send it back. They put the blade way down below the table. How the heck do they think it’s supposed to cut like that? CSull, OCtoolguy, jbrowning and 3 others 1 5 Quote Link to comment Share on other sites More sharing options...
rjweb Posted April 6, 2022 Report Share Posted April 6, 2022 Are you saying you cannot raise the blade, that sucks OCtoolguy and kmmcrafts 2 Quote Link to comment Share on other sites More sharing options...
Needmore Posted April 6, 2022 Report Share Posted April 6, 2022 I also have a Dewalt Job site Table Saw. There should be a crank on the front to raise and lower the blade. kmmcrafts and OCtoolguy 1 1 Quote Link to comment Share on other sites More sharing options...
Dan Posted April 6, 2022 Report Share Posted April 6, 2022 Kevin, fold the legs in. When the table goes down the blade should be about right. LOL Did you buy it on April 1? OCtoolguy, barb.j.enders and kmmcrafts 3 Quote Link to comment Share on other sites More sharing options...
jbrowning Posted April 7, 2022 Report Share Posted April 7, 2022 You need a larger saw blade (XXL I'm thinking). LOL Jim kmmcrafts and OCtoolguy 2 Quote Link to comment Share on other sites More sharing options...
Gonzo Posted April 7, 2022 Report Share Posted April 7, 2022 Kevin, if you read the very fine print in the instruction book, it says to use a metric crescent wrench when assembling table. I would venture to say you used an ASA standard crescent wrench when assembling. danny, Gene Howe, OCtoolguy and 1 other 4 Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted April 7, 2022 Author Report Share Posted April 7, 2022 4 hours ago, rjweb said: Are you saying you cannot raise the blade, that sucks Sorry, I was just joking around, I wondered if anyone would catch it as a joke or not. LOL danny, jbrowning and OCtoolguy 3 Quote Link to comment Share on other sites More sharing options...
barb.j.enders Posted April 7, 2022 Report Share Posted April 7, 2022 10 hours ago, kmmcrafts said: Sorry, I was just joking around, I wondered if anyone would catch it as a joke or not. LOL I got "sucked in" on one of your previous April 1 jokes, so always a little suspicious of your early April posts. kmmcrafts, danny and OCtoolguy 1 2 Quote Link to comment Share on other sites More sharing options...
Bill WIlson Posted April 7, 2022 Report Share Posted April 7, 2022 11 minutes ago, barb.j.enders said: I got "sucked in" on one of your previous April 1 jokes, so always a little suspicious of your early April posts. So, is it April Fools month now? I'm just trying to keep up. kmmcrafts, meflick and OCtoolguy 2 1 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted April 7, 2022 Report Share Posted April 7, 2022 You're about 7 days late Kevin. But, better late than never. kmmcrafts 1 Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted April 7, 2022 Author Report Share Posted April 7, 2022 9 hours ago, Bill WIlson said: So, is it April Fools month now? I'm just trying to keep up. 4 hours ago, OCtoolguy said: You're about 7 days late Kevin. But, better late than never. So people expect it on the 1st so I run my jokes late, lol.. I have another one I wanted to do but I suppose it'll have to be next year. barb.j.enders, OCtoolguy and meflick 3 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted April 8, 2022 Report Share Posted April 8, 2022 1 hour ago, kmmcrafts said: So people expect it on the 1st so I run my jokes late, lol.. I have another one I wanted to do but I suppose it'll have to be next year. Oh go ahead. If you are anything like me, next year you won't remember it. barb.j.enders and kmmcrafts 1 1 Quote Link to comment Share on other sites More sharing options...
timelett Posted April 8, 2022 Report Share Posted April 8, 2022 That way you can practice your cuts. OCtoolguy and kmmcrafts 2 Quote Link to comment Share on other sites More sharing options...
Jim McDonald Posted April 8, 2022 Report Share Posted April 8, 2022 On 4/6/2022 at 4:34 PM, kmmcrafts said: So I put my new table saw together a few minutes ago and this is so dumb on their part. I gotta send it back. They put the blade way down below the table. How the heck do they think it’s supposed to cut like that? A zero insert is one thing, but that is the new zero kerf model. OCtoolguy 1 Quote Link to comment Share on other sites More sharing options...
crupiea Posted April 9, 2022 Report Share Posted April 9, 2022 Its obviously one of those new safer, gentler saws. If it doesnt make any noise or tun on it will be the safest of all. lol OCtoolguy 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.