DWSUDEKUM

You might wish to look into this: Running rough from Kip Scrollin' with an Ex-21 http://tidewater-creations.com In recent months it has slowly but surely started running rough. Not really a vibration like before but seems to be in the upper arm. If I lift up on the arm the sound and vibration stop. I didn't realize how bad it had gotten until today when the speed control knob started clanging and I tightened set screw to fix it. Took note stock of the situation and realized how bad things are. An update...decided to wait till after the holidays to phone Ray @ Seyco as I was sure this was going to be a long process that involved taking the machine apart and tracking down various potential issues. Well of course I was wrong and it took all of 1 minute for Ray to diagnose...LOL Did have to modify a wrench but all is well My problem developed over time and it's best described as running rough with sounds and vibration getting much worse as speed is increased. At full speed the quick release lever would pop open. The repair was simple: remove cover from back of saw opposite motor and tighten screw in cut out area. If screw continues to turn you must apply a modified 8mmwrench to the back side and hold bolt. Tighten firmly. As shown you must add a "bend" in the wrench. You can heat it and bend it in a vise or take a hammer and beat the tar out of it. I fully recommend the later as it works great and is a stress reliever as well I have added pics in case this wasn't clear. DW

Love them both Fish especially the Wolf done on that live edge slab. Thanks for sharing this with us. DW

Excellently done Dick. He is going to be very pleased with this. Thanks for sharing this with us. DW

Very nice Ralph. I especially like that last one. Thanks for sharing these with us. DW

Excellently done Dick. He should really like that and it will give him years of good service for his headphones. Thanks for sharing this with us. DW

Excellently done Dan. Thanks for sharing this with us DW

Love that Randy. That came out great. Always knew that you could deface coins as long as you did not try to pass it off as another value otherwise those penny rolling machines would not have been so popular in the carnivals and amusement parks. What got you into coin cutting Randy? DW

Very nicely done. Thanks for sharing these with us. DW

Monti that sure is different. I like it though, Thanks for sharing this with us. DW

Very nicely done Mimi. Thanks for sharing this with us. DW

That came out great Dan. One could use it for small wood scraps for Intarsia as well. Thanks for sharing this with us. DW

Sorry hear about that Dan, this happens to all of us from time to time. I got to the point were I work on a table and never in free air. The piece is flat on the table where it is supported. I got tired of either enlarging the designer firewood pile or gluing it back together. DW

That came out great. Thanks for sharing this with us. DW

That came out great Randy. That has Celtic overtones in that all the lines cross and are intertwined. Thanks for sharing this with us. DW

Nicely done Edward. Thanks for sharing this with us. DW

Excellently done Bob. Thanks for sharing them with us. DW

The first was for the folks down under in Australia the other for the rest of us Great job on that I really like that. Thanks for sharing this with us. Love live edge wood use. DW

Nicely done Joe. Wonder what it would look like with a little darker background? Thanks for sharing this with us. DW

No problem Dick. You still did a great job on that. Thanks for the correction and the pic of the mirror. DW

Dick spirals take practice and you look like you are greeting a good bit of it. Thanks for sharing this with us. DW

Excellently done Ron. Those are very nice. Thanks for sharing these with us. DW

Nicely done so far. Thanks for sharing this WIP with us. DW

Mega points for that one Dick. That came out great! Thanks for sharing this with us. DW

Excellently done Jerry. That could become a wall hanging as well. Thanks for sharing this with us. DW

Kevin, That latest batch came out great. You should put all order on hold, temporally, and load the pod. Thanks for sharing these with us. DW