Jump to content

jollyred

SSV Patron
 View Profile  See their activity

  • Posts

    869

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by jollyred

  1. jollyred
    I use the test tube holders, in which I put the slip of paper sent with the blades to show which blade is in there. I made a holder to attach to the scroll saw stand that holds the tube for the blades I am currently using. The rest of the tubes go in a compartmented box that I keep in the bottom of the stand. That way I don't have to remember which blade is in the saw. With my memory, that is important. Tom
  2. jollyred
    I generally use Aileen's clear tacky glue. Just put small drops in the area I want the glue, then spread it around with my finger. I do try to keep it away from the edges of the frets, and keep the glue thin. Once the overlay is in position, I will use a pin nailer to secure it from the back, if the wood is thick enough to keep the nails from going all the way through. Otherwise, I don't bother with the pin nails. The nails are just in case the glue should fail, so I only use a few around the edges. I have some 3/8" pin nails, so most of my projects are 1/2" finished thickness. Pin nails are also good for reinforcing butt and miter joints in thin material. Tom
  3. jollyred
    Beautiful work. Glad you decided to stay. Tom
  4. jollyred
    Like that one. You did a nice job cutting it. Tom
  5. jollyred
    Some paneling has a MDF core or backing, this may be what he is using, or at least similar. Tom
  6. jollyred
    You can also use a hinge bit (formerly known as a Vix bit) to set the holes. These self center on the hinge screw hole, and the depth can be controlled. If you plan on making a number of these, the hinge bit is the way to go. Just be sure the bit is sized to fit your screw. https://www.homedepot.com/p/RYOBI-Self-Centering-Hinge-Bit-A99SCHB1/312284028?mtc=Shopping-B-F_D25T-B-D25T-25_7_POWER_TOOL_ACCESSORIES-Multi-NA-Feed-LIA-NA-NA-PowerToolAccessories&cm_mmc=Shopping-B-F_D25T-B-D25T-25_7_POWER_TOOL_ACCESSORIES-Multi-NA-Feed-LIA-NA-NA-PowerToolAccessories-71700000071858300-58700006314327728-92700057006649503&msclkid=4f625f0da6f61376d3a1009b822b39b7&gclid=4f625f0da6f61376d3a1009b822b39b7&gclsrc=3p.ds Otherwise, using a gimlet or awl to mark the center of the hinge hole then drilling the hole is a good way to do it. Tom
  7. jollyred
    Go to your scrap pile and get another board. Since you cut it before, it should cut all right again. If you still have the problem, it's the saw or blade. If it cuts all right, it's the wood. Tom
  8. jollyred
    I think I would fill first. It would be kind of hard to get the epoxy flush with the surface if filled after the cutting. At least I think so, but I don't like sanding any more than necessary. By the way, that's a nice pattern, and we will need pictures when it is finished. That's the price you pay for our valuable free advice. Tom
  9. jollyred
    Decided to make a Halloween lamp this year, and came up with the lamp below. Saw where Steve Good had used a flame effect led bulb in a project and liked the idea a lot, so I got one for this project. The flickering light from this bulb really makes the lamp interesting. The image of the cat is downloaded from the internet. Cut from 1/4" BB, with a frosted mylar sheet for the background. Spray painted black. About 6" wide and 8" high and 3" deep. I don't know why the light from the bulb is yellow, in real life it is all pumpkin orange, like the color in the bats. Guess using a phone to take pictures is iffy. Tom
  10. jollyred
    Welcome to the Village. Good to have you here. You will find a lot of information and (mostly) good advise here. Tom
  11. jollyred

    Turtle

    jollyred replied to FrankEV's topic in Bragging Rights

    Great job. The paint really makes it pop. Tom
  12. jollyred
    Some of the lesser celebrated holidays, such as Labor Day, St. Patrick's day, Ground Hog day, etc. Tom
  13. jollyred
    You can also convert in gimp, if you have that. Tom
  14. jollyred
    Jewelers must be able to cut it, since mother of pearl is used in jewelry, also pen making and used to be made into buttons. I would try to research how those guys do it. I would think a jeweler's blade would cut it. Tom
  15. jollyred
    When my bottle of ca has the end closed with dried glue, I take a knife and pop off the plug. Cut from the bottom of the plug on the side of the nozzle and cut towards the end of the nozzle. Might have to take a couple of cuts, but it will pop out the plug in the nozzle. Tom
  16. jollyred
    Quick, cheap and it works great. What's not to like?
  17. jollyred
    The way the stain soaked into the end grain on the cut lines makes it look like they had a finish applied before staining. Tom
  18. jollyred
    Steve Good made the suggestion at one time that using a slightly dull blade can help. Haven't tried it myself, YMMV. Tom
  19. jollyred
    I usually nail them together. Putting the nails to the outside of the pattern gives a good hold, and there are no nail holes to contend with. I use a 23ga pin nailer, with 3/8" or longer pins. I just use a file to smooth any ends that stick out. It's on the back, so any scuffing from the file won't show. Tom
  20. jollyred
    I would think an iron on cloth patch would work pretty well. just cut a strip about and inch wide and iron it onto the backs of the plywood halves. Tom
  21. jollyred
    Good idea, but I wouldn't hang anything heavy on it. Tom
  22. jollyred
    Darn you! I am going to make the original Steve Good pattern for a Christmas present this year. Now I am going to have to wonder if I will redesign it I really like your idea, and may have to do something similar, but different. You did too good a job on that. Tom
  23. jollyred
    What speed are you cutting? Higher speeds will increase heat, and the plastic melts. Try recutting the line at the slowest speed your scroll saw has. If that doesn't work, try lubricating the blade with a little wax, such as from a candle. Final idea, use a little spray bottle to keep a bit of water on the cutting area. Be careful to not get water in the electrics. Dry thoroughly afterwards. Tom
  24. jollyred
    I have used small decorative brass hinges on boxes like that. You can get them at most of the box stores and hardware stores. They come with small nails to hold them on, which I don't like, so I got some 1/4" brass screws to use with them. With 1/4" wood, you may need to file or grind off the very tip so they don't go all the way through the wood. The screws will need predrilled holes to fit into, but they hold a lot better than nails. I use a hinge bit to drill the holes, which makes life a little easier. By the way, I like the box. You did a great job on it. Someone is going to be very happy. Tom
  25. jollyred
    I don't know how to solve your problem, but one work around might be to print to pdf, then see if that works. If it is correct, then the problem is with your printer reading Inkscape. You might need to download new drivers for it. And you can print the pattern from the pdf file. Tom
×
×
  • Create New...