ike
-
Posts
4,275 -
Joined
-
Last visited
-
Days Won
5
Content Type
Store
Profiles
How-To & Articles
Scroll Saw Reviews
Clubs & Organizations
Clubs & Organizations International
Pattern Shop
Suppliers
Village University
Help Desk
Forums
Gallery
eBooks
Everything posted by ike
-
I have thought about a face book page but my wife is on face book and it would probably mess her up . so i have stayed off. i do most of my selling at about Christmas time, I keep my moneys separate and I still have about $300 in the kitty,so i will probably stay with that method. IKE
-
I very welcome use High speed , i usually run at about #6. Mine did it last year and it finally started to vibrate at about #6 so i took it in for warranted work IKE
-
I have never heard of it. Is a saw to take psinless blades, if it doesn't take pin less blades you will be ready for a new saw in a couple of weeks. IKE
-
That was good for the first cut. Welcome from Ohio.+Here is a couple of hints . Get some wax for the table I use Turtle past wax. It does 2 things It keeps down the rust and the wood slides easier.Let the saw all the work. Norw if you have any questions we have answers, and we like pictures. IKE
-
no matter which saw you buy ;. you want a foot peddle to go with it turn on the saw and ut Duct tape over the on swith, for some reason they both have this problem, IKE
-
nice cutting thanks for showing IKE
-
Ray there may be a nut connecting the motor to the arm that is loose. I hope this is clear i not sure what every thing is called.
-
I have been running mine for 1 1/5 years and never had any problem with the blade out of square. That was the first thing I checked due to my problem with other saws i have owned,
-
One thing about varnish and suck you apply it with a brush let it dry then take 400 / 6000 grit emery and ssand it before the 2 coat let it dry and use 600 oly grit to finish it . one other t=hing about varnish which is all i use yo thin it down by 10% this allows the varnish to flow togather and leaves no brush marks , just don't put it on too heavy light coats does the job.
-
Kevin these alr all scrap from the Mill it's the end pieces that are under 6 ' in length any long pieces are less than 1 in thick there not many pieces like that. but a 4 ' is ni;ce for me because they are easy to store. and they are FREE
-
When you have tried all the suggestions take it to a De Walt repair shop in your area-if it is on warranty if not it could cost you $$$ here in the Cincinnati area the cast runs $35 to $250. It will only get worse,
-
I just got back from the local Saw Mill with a pretty good load in my Truck by the time I got rid of the trash I ended up with about 100 ft of Maple. the thickness was between 3/4 and 1 1/4 This is green so It will have to be dried out . It probably won't be ready till next spring. I also got 16 ft. of Walnut 5/8 thick X 8 in. this is ready to be planed. I have some walnut and cherry that is left from what I got last year It. s ready to plain, With Saw Mill lumber yu need to get it one year in advance
-
Nice work Kevin . The key rings look good , I have made some but I like the cedar one best. i have a bunch of 3/8 cedar that would look nice for that.. Thanks for showing.
-
Nice designs and cleqan cuts thanks for showing
-
NICE BOWL i LIKE IT.
-
looks lik you aced it. IKE
-
Switching to plain end blades-troubleshooting
ike replied to Scrappy's topic in General Scroll Sawing
Did the blade come loose or did it slip in the holder.. if either of these happened get some lock seize from a hardware store and put some on the holding screws . A tube cost about $4 and will be enough to last a life time. It worked for me. IKE -
Welcome to the village. Nice projects you have there. good fit on the tissue boxes. IKE
-
I agree with Larry I had a problem with ti;gating the blade until I used anti seize. I got a tube at the hardware stor for about $4 and it is enough to last a lifetime I don't see the nobs coursing any problems, I have a DW 788 and after about 700 hours it developed a problem I took it into the DeWalt repair shop and thy fixed it at no cost because it was still guarantee. IKE
-
That is nice art work . IKE
-
nice I like the curved one best IKE
-
Welcome Jen .that picture is very nice and interesting.I am from south western Ohio home of the Reds. Hope to see more pictures in the future. If you have any questions there is plenty of help here and plenty of free patterns. IKE
-
Nice deer picture. I printed it off once but never got to cutting It now I don't know what I did with the pattern
-
Nice work again . take it easy.
